title: COSEL Power Supply, Noise Filter 2025 Product Catalog

Summary

COSEL Power Supply, Noise Filter 2025 Product Catalog

AC-DC Power Supplies Enclosed TypeFETA3000BCOrdering informationFET A 3000 B C -OO -O1 2 3 4 5 6 7FETARExample recommended EMI/EMC filterNAC-20-472High voltage pulse noise type : NAP seriesLow leakage current type : NAM series* A higher current rating EMI/EMC filtermay be recommended in view of theother devices that could be connectedin parallel with the power supply.1 Series name2 Single output3 Output wattage4 200/230V input5 Version6 Output voltage7 OptionalR: with Remote ON/OFFPositive logic control*Make sure necessary tests will be carried out on your end equipment with the power supply installed in accordance with any required EMC/EMI regulations.MODELFETA3000BC-250MAX OUTPUT WATTAGE[W]3000DC OUTPUT250V 12ASPECIFICATIONSMODELFETA3000BC-250VOLTAGE[V]AC170 - 264 1f (Output derating is required at AC170V - 180V. Refer to“Derating”)CURRENT[A]ACIN 200V16.8typFREQUENCY[Hz]50 / 60 (47 - 63)INPUTEFFICIENCY[%]ACIN 230V93typ (Io=50%)91.5typ (Io=100%)POWER FACTORACIN 230V0.98typ (Io=100%)INRUSH CURRENT[A]ACIN 200V*120max / 80max (Primary inrush current /Secondary inrush current) (More than 10 sec. to re-start)LEAKAGE CURRENT[mA]0.85max (ACIN 240V 60Hz, Io=100%, According to IEC62368-1)VOLTAGE[V]250CURRENT[A]LINE REGULATION[V]1.0maxLOAD REGULATION[V]2.5maxRIPPLE[Vp-p]0 to +40C *2 12maxRIPPLE NOISE[Vp-p]OUTPUT-10 to 0C *2 13.2maxTEMPERATURE REGULATION[V]DRIFT[V]*31.0maxSTART-UP TIME[s]1.0max (ACIN 200V, Io=100%)HOLD-UP TIME[ms]ACIN 200V10typ (Io=100%)20typ (Io=50%)OUTPUT VOLTAGE ADJUSTMENT RANGE[V] *4180 - 350OUTPUT VOLTAGE SETTING[V]250 - 253Activate over 105% - 120% of rated current and recovers automatically.OVERCURRENT PROTECTION(Output voltage shuts down when the output voltage continuously drops due to overcurrent protection.) *5PROTECTIONOVERVOLTAGE PROTECTION[V] *5 400 - 450 (Active over 160%-180% of rated voltage.) *6CIRCUIT ANDDC_OK LAMPLED (Green)OTHERSALARM LAMPLED (Amber)REMOTE ON/OFFProvidedINPUT-OUTPUT-RC-WRN-PGAC3,000V 1minute, Cutoff current = 25mA, DC500V 50MΩmin (At room temperature)INPUT-FGAC2,000V 1minute, Cutoff current = 25mA, DC500V 50MΩmin (At room temperature)ISOLATIONOUTPUT-FGAC2,000V 1minute, Cutoff current = 25mA, DC500V 50MΩmin (At room temperature)RC-WRN-PG-FGAC500V 1minute, Cutoff current = 100mA, DC500V 50MΩmin (At room temperature)OUTPUT-RC-WRN-PGAC3,000V 1minute, Cutoff current = 25mA, DC500V 50MΩmin (At room temperature)OPERATING TEMP.,HUMID.AND ALTITUDE-10 to +70C (Refer to“Derating”), 20 - 90%RH (Non condensing), 3,000m (10,000 feet) maxENVIRONMENTIMPACT196.1m/s 2 (20G), 11ms, once each along X, Y and Z axisAGENCY APPROVALSUL62368-1, C-UL (CSA62368-1), EN62368-1SAFETY ANDCONDUCTED NOISEComplies with FCC Part 15-A, CISPR32-A, EN55032-A, VCCI-ANOISE REGULATIONSHARMONIC ATTENUATOR Complies with IEC61000-3-2 Class A *7OTHERS*1 The current of input surge to a built-in noise filter (0.2ms or less) is excluded.*2 Measured by 500MHz oscilloscope.Ripple and ripple noise is measured on measuring board with capacitor of 2.2μF within150mm from the output terminal.*3 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C,with the input voltage held constant at the rated input/output.*4 Can't be used above the rated output current and the rated output power.*5 Output voltage recovers from protection by shutting down the input voltage and waitingmore than 10 seconds then turning on AC input again, or turning off the output voltage byremote control.*6 Since the voltage adjustment range is wide, the operating voltage of the overvoltageprotection is set high.*7 Please contact us about another class.*8 Case size contains neither the terminal blocks, connector and screw.* To meet the specifications, do not operate over-loaded condition.* A sound may occur from power supply at peak loading.FETA-6? 118 ?