title: COSEL Power Supply, Noise Filter 2025 Product Catalog

Summary

COSEL Power Supply, Noise Filter 2025 Product Catalog

AC-DC Power Supplies Open FrameLHA150FOrdering informationLH A 150 F -OO -O1 2 3 4 5 6LHALHA-14RThis power supply is manufactured by SMD technology. The stress to PCB like twisting or bending causes the defect of the unit, so handle the unit with care.*Make sure necessary tests will be carried out on your end equipment with the power supply installed in accordance with any required EMC/EMI regulations.MODELLHA150F-12LHA150F-24LHA150F-36LHA150F-48MAX OUTPUT WATTAGE[W]*2150151.2151.2153.6DC OUTPUT*212V 12.5A24V 6.3A36V 4.2A48V 3.2ASPECIFICATIONS1 Series name2 Single output3 Output wattage4 Universal input5 Output voltage6 Optional *1C : with CoatingG : Low leakage currentJ4 : EP (TE Connectivity) connector typeR2 : with Remote ON/OFFS : with ChassisSN : with Chassis & coverU1 : Can be attached the externalcapacitor unitY : with PotentiometerFor option details, refer toInstruction Manual 6.MODELLHA150F-12LHA150F-24LHA150F-36LHA150F-48VOLTAGE[VAC]*285 - 264 1f (Refer to“Derating”and Instruction Manual 1.1)CURRENT[A]FREQUENCY[Hz]50 / 60 (45 - 66)ACIN 100V 86.5typ 89.0typ 89.5typ 90.0typEFFICIENCY[%]INPUTACIN 230V 89.5typ 92.0typ 92.5typ 93.0typACIN 100VPOWER FACTOR (Io=100%) 0.99typACIN 230V 0.91typACIN 100V 15typ (Io=100%) Ta=25C at cold startINRUSH CURRENT[A]ACIN 230V 35typ (Io=100%) Ta=25C at cold startLEAKAGE CURRENT[mA]0.40 / 0.75max (ACIN 100V / 240V 60Hz, Io=100%, According to IEC62368-1 and DEN-AN)VOLTAGE[V]12243648CURRENT[A]*212.56.34.23.2LINE REGULATION[mV]*348max96max144max192maxLOAD REGULATION[mV]*3100max150max240max240max0 to +50C *7 120max 120max 150max 150maxRIPPLE[mVp-p]-10 to 0C 160max 160max 200max 200max*4Io=0 to 10% 160max 160max 200max 200maxOUTPUT0 to +50C *7 150max 150max 250max 250maxRIPPLE NOISE[mVp-p]-10 to 0C 180max 180max 300max 300max*4Io=0 to 10% 230max 230max 300max 300maxTEMPERATURE REGULATION[mV]DRIFT[mV]*548max96max144max192maxSTART-UP TIME[ms]700typ (ACIN 100V, Io=100%)HOLD-UP TIME[ms]20typ (ACIN 100V, Io=100%)OUTPUT VOLTAGE ADJUSTMENT RANGE[V]Fixed (“Y”option is available for adjusting output voltage between +10%, -5%)OUTPUT VOLTAGE SETTING[V]11.50 to 12.5023.00 to 25.0034.50 to 37.5046.00 to 50.00OVERCURRENT PROTECTIONWorks over 105% of rating and recovers automaticallyPROTECTION OVERVOLTAGE PROTECTION13.80 to 16.8027.60 to 33.6041.40 to 50.4055.20 to 67.20CIRCUIT AND OPERATING INDICATIONNot providedOTHERSREMOTE SENSINGNot providedREMOTE ON/OFFOption (Refer to Instruction Manual 6.1)INPUT-OUTPUT . RC*8AC3,000V 1minute, Cutoff current = 10mA, DC500V 100MW min (At Room Temperature)ISOLATIONOUTPUT-RC*8AC100V 1minute, Cutoff current = 25mA, DC100V 10MW min (At Room Temperature)OPERATING TEMP.,HUMID.AND ALTITUDE *2-10 to +70C, 20 - 90%RH (Non condensing), 5,000m (16,500feet) max (EN62477-1 (OVC III) : 2,000m (6,600feet) max)ENVIRONMENTIMPACT196.1m/s 2 (20G), 11ms, once each X, Y and Z axisSAFETY ANDAGENCY APPROVALSUL62368-1, C-UL (equivalent to CAN/CSA-C22.2 No.62368-1), EN62368-1, EN62477-1 (OVC III), Complies with DEN-ANNOISECONDUCTED NOISEComplies with FCC-B, VCCI-B, CISPR11-B, CISPR32-B, EN55011-B, EN55032-BREGULATIONSHARMONIC ATTENUATOR *6Complies with IEC61000-3-2 (Class A)OTHERS*1 The listed options may affect the published standardspecifications. Please contact us for detailed productspecifications.*2 Derating is required.*3 At low load conditions, the burst mode operation will start. To checkload regulation, you will need to measure the characteristics ataverage mode with instruments.*4 This is the value that measured on measuring board with capacitorof 22mF and 0.1mF at 150mm from output terminal. Measuredby 20MHz oscilloscope or Ripple-Noise meter (Equivalent toKEISOKU-GIKEN:RM104).Ripple and ripple noise spec is change at Io=0 to 10% by burstoperation.*5 Drift is the change in DC output for an eight hour period after a halfhourwarm-up at 25C, with the input voltage held constant at therated input/output.*6 Please contact us about another class.*7 12V output product, the maximum temperature of 40C.? 188 ?Example recommended EMI/EMC filterEAC-03-472High voltage pulse noise type : EAP seriesLow leakage current type : EAM series* A higher current rating EMI/EMC filtermay be recommended in view of theother devices that could be connectedin parallel with the power supply.*8 Applicable when Remote ON/OFF (optional) is added.* To meet the specification, do not operate overload condition.* Parallel operation is not possible.* Sound noise may be generated by power supply in case of pulseload.