title: COSEL Power Supply, Noise Filter 2025 Product Catalog

Summary

COSEL Power Supply, Noise Filter 2025 Product Catalog

(X)(X)180-240VACREMOTESIGNALON/OFFPARALLELOPERATIONSIGNALSYSTEMON/OFFALMMONITOR(X)(X)48VDC(X)(X)(X)(X)(Y)(X)(X)REMOTE SI GNAL ON1 2 3 4(X)(X)(X)(X)(X)(X)(Y)(X)(X)(X)(X)(X)(X)REMOTESIGNALON/OFFSIGNALFUNCTIONSYSTEMON/OFFALMMONITOR48V REMOTE SI GNAL ONDC 1 2 3 4(X) (X) (X) (X) (X) (X) (X) (X) (X) (X)(X) (X)(X)(X)(X)(X) (X)(X)(X)(X)(Y)180-240VACAC-DC Power Supplies Enclosed TypeInstruction Manual1 Functions1.1 Input Voltage Range!The input voltage range is AC160-264V (three-phase).!In cases that conform with safety standard, input voltage range isAC180-AC240V (50/60Hz).!In the case of three-phase four-wire system, connect the threewires to input terminal, except ground wire.!If the wrong input or single phase input is applied, the unit will notoperate properly and/or may be damaged.AC160 - 264VAC160 - 264VDelta connectionStar connectionFig.1.1 Connection method1.2 Inrush Current Limiting!An inrush current limiting circuit is built-in.!If you need to use a switch on the input side, please select onethat can withstand an input inrush current.!Thyristor technique is used in the inrush current limiting circuit.When you turn the power ON/OFF repeatedly within a short periodof time, please have enough intervals so that the inrush currentlimiting circuit becomes operative.!When the switch of the input is turned on, the primary inrush currentand secondary inrush current will be generated because thethyristor technique is used for the inrush current limiting circuit.1.3 Overcurrent Protection!An overcurrent protection circuit is built-in and activated over105% - 120% of the rated current. A unit automatically recoverswhen a fault condition is removed.Please do not use a unit in short circuit and/or under an overcurrentcondition.!Low-voltage protection is activated when output voltage is reducedby over current protection under the low-voltage protectionvalue.to operate a motor, etc., please install an external diode on theoutput terminal to protect the unit.1.5 Low-voltage Protection!Low-voltage protection is built-in. This protection will shut downthe output with the activation. To restart the output, recycle AC inputafter 3 or more seconds.1.6 Thermal Protection!A thermal protection circuit is built-in.The thermal protection circuit may be activated under followingconditions and shut down the output.1Continuous over current 208A or more.2Continuous over wattage 9984W or more.3When the cooling which deviates from referred to“Assemblingand Installation Method”are consecutive.4When a fan stops or air flow is blocked from the fan and weakens.If the thermal protection circuit is activated, shut off the input voltageand eliminate all the overheating conditions. To recover the outputvoltage, have enough time to cool down the unit before turning onthe input voltage again.1.7 Output Voltage Adjustment!To increase an output voltage, turn a built-in potentiometer clockwise.To decrease the output voltage, turn it counterclockwise.!Output Voltage Adjustment is 43.2 - 52.8V.!Output Voltage factory setting is 47.0 - 49.0V.INPUT 3f180-240VAC 39ATB1RSTFGCN1CN3CN5CN7CN9CN2CN4CN6CN8CN10HV.ADJOUTPUT(A) 48VDC TOTAL 208A20A20A 20A 20A 20A 20A 20A 20A 20A 20A1 2 3 4 5 6 7 8 9 10OUTPUT(B) 48VDC TOTAL 208A20A 20A 20A 20A 20A 20A20A 20A20A20A11 12 13 14 15 16 17 18 19 20Output voltage adjustable potentiometerFig.1.2 SCHA10000T Output voltage adjustable potentiometer20A120A 20A 20A 20A 20A 20A2 3 4 5 6 7INPUT 3f180-240VAC 39ATB1RS1.4 Overvoltage Protection!An overvoltage protection circuit is built-in. If the overvoltage protectioncircuit is activated, shut down the input voltage, wait morethan 3 seconds and turn on the AC input again to recover the outputvoltage.20A820A9OUTPUT 48VDC TOTAL 208A20A 20A 20A10 11 1220A1320A14V.ADJFig.1.3 SCDA10000T Output voltage adjustable potentiometerH(Y) (X) (X) (X)CN1CN3CN5CN7(X) (X) (X)CN2CN4CN6CN8SECONDARY TERMINAL-STFGOutput voltage adjustable potentiometerNote :!Please avoid applying a voltage exceeding the rated voltage to anoutput terminal. Doing so may cause a power supply to malfunctionor fail. If you cannot avoid doing so, for example, if you needSC-11