title: COSEL Power Supply, Noise Filter 2025 Product Catalog

Summary

COSEL Power Supply, Noise Filter 2025 Product Catalog

20A1(X)20A8(X)20A2(X)20A9(X)20A 20A 20A3 4 5(X)OUTPUT 48VDC TOTAL 208A(X)(X)20A 20A 20A10 11 12(X)(X)(X)20A6(X)20A13(X)20A7(X)20A14(X)REMOTESIGNALON/OFFSIGNALFUNCTIONSYSTEMON/OFFALMMONITOR48V REMOTE SI GNAL ONDC 1 2 3 4V.ADJHCN1CN3CN5CN7(Y)180-240VACCN2CN4CN6CN8INPUT180-240VACTB1RSTFG3f39ATB1TB1INPUT180-240VACINPUT180-240VAC3f39A3f39ARSTFGRSTFG180-240VACREMOTESIGNALON/OFFPARALLELOPERATIONSIGNALSYSTEMON/OFFALMMONITOR180-240VACREMOTESIGNALON/OFFPARALLELOPERATIONSIGNALSYSTEMON/OFFALMMONITORINPUT 3fOUTPUT(A) 48VDC TOTAL 208A180-240VAC 39ATB1180-240V 48V REMOTE SI GNAL ONAC DC 1 2 3 4RCN1CN2REMOTES SIGNALON/OFFCN3CN4TPARALLELOPERATIONCN5CN6SIGNALFGSYSTEMON/OFFCN7CN8ALMMONITOR48VDC(X)(X)(X)(X)(Y)48VDC(X)(X)(X)(X)(Y)(X)(X)(X)(X)(Y)CN1CN3CN5CN7CN9CN1CN3CN5CN7CN9CN9REMOTE SI GNAL ON1 2 3 4(X)(X)(X)(X)(Y)REMOTE SI GNAL ON1 2 3 4(X)(X)(X)(X)(Y)(X)(X)(X)(X)(Y)CN2CN4CN6CN8CN10V.ADJCN2CN4CN6CN8CN10V.ADJCN10V.ADJHHHOUTPUT(A) 48VDC TOTAL 208AOUTPUT(A) 48VDC TOTAL 208A20A1(X) (X) (X) (X) (X) (X) (X) (X) (X) (X)20A11(X) (X)(X)(X)(X)(X) (X)(X)(X)(X)20A1(X) (X) (X) (X) (X) (X) (X) (X) (X) (X)20A1120A220A1220A220A1220A320A1320A320A1320A420A 20A 20A20A20A14 15 16 17 1820A420A520A520A 20A 20A20A20A14 15 16 17 1820A 20A 20A8 9 10(X) (X)(X)(X)(X)(X) (X)(X)(X)(X)20A20A 20A 20A 20A 20A 20A 20A 20A 20A1 2 3 4 5 6 7 8 9 10(X) (X) (X) (X) (X) (X) (X) (X) (X) (X)OUTPUT(B) 48VDC TOTAL 208A20A 20A 20A 20A 20A 20A20A20A 20A 20A11 12 13 14 15 16 17 18 19 20(X) (X)(X)(X)(X)(X) (X)(X)(X)(X)20A6OUTPUT(B) 48VDC TOTAL 208A20A6OUTPUT(B) 48VDC TOTAL 208A20A720A720A 20A 20A8 9 1020A1920A1920A2020A20AC-DC Power Supplies Enclosed TypeInstruction Manual!Internal output fuse may open with over current.To repair the opened fuse, please return the unit to us with a Coselissued RMA.!In case of the parallel operated connection without the bus bar asshown in Fig.2.5, the difference of impedance of load wires of eachunit and connectors causes difference of output current of eachunit and connectors.Therefore, connection using the parallel bus bar as shown inFig.2.5 is required to parallel operation.Output ConnectorsInstall H-PA-8MASSLVCTBPCNTCOMNo.1(MASTER)(Y) (X) (X) (X)(X) (X) (X)SECONDARY TERMINAL-SInstall H-PA-7MASSLVCTBPCNTCOMMASSLVCTBPCNTCOMNo.2(SLAVE)No.3(SLAVE)Fig.2.3 Output of SCDA10000T(a)Connection of signalinternal moduleinternal module14 Fuses(30A)fuses are connected to the +V(There is no fuse in -V)OUTPUT(A)Bus bar¶Material :copper C1100,C1020:electrical conductivity(IACS)more than 98%¶cross section area :more than 300mm 2¶length :less than 600mminternal module14 connectorsOUTPUT(B)Fig.2.4 Output part block diagram2.2 Parallel Operation? SCHA10000T!Parallel operation is up to 3 units as following Figure2.5.Each output terminal block [OUTPUT(A)] should be connectedparallel and CTB/COM as well. MAS of the master unit and SLV ofall slave units must be connected with H-PA-8, H-PA-7.!Differences in the output current values among the power suppliesin parallel connection are 5% at most. Please make sure that thesum of the output current values does not exceed a value obtainedfrom the following equation.? SCDA10000T(b)Connection of bus barFig.2.5 Example of parallel connection!Parallel operation is not possible.(Output current in parallel operation)= (Rated current per unit) X (Number of unit) X 0.95!Each connector of OUTPUT(B) of each unit which is connected inparallel has 20 amps drawing capability.!Internal output fuse may open with over current.To repair the opened fuse, please return the unit to us with Coselissued RMA.!Output voltage is adjustable by adjusting the master unit potentiometer(One control mode).!Parallel connection with other products is not allowed.!In case of use PCNT, all of power supplies will stop, if either of thepower supply fail.SC-14