title: COSEL Power Supply, Noise Filter 2025 Product Catalog

Summary

COSEL Power Supply, Noise Filter 2025 Product Catalog

AC-DC Power Supplies PCB Mount TypeTEPS65FOrdering informationTEP S 65 F OO -O1 2 3 4 5 6Rwith Cover(option : -N)Example recommended EMI/EMC filterEAM-03-000High voltage pulse noise type : EAP series150KHz-1MHz (To safety ground the secondaryside) : EAC serie* A higher current rating EMI/EMC filtermay be recommended in view of theother devices that could be connectedin parallel with the power supply.1 Series name2 Single output3 Output wattage4 Universal input5 Output voltage6 Optional *1E2: Low leakage currentH : with output peak current(12V,24V)N : with coverFor option details, refer toInstruction Manual 8.TEPSStandard typeClassⅡThis power supply is manufactured by SMD technology. The stress to PCB like twisting or bending causes the defect of the unit, so handle the unit with care.*Make sure necessary tests will be carried out on your end equipment with the power supply installed in accordance with any required EMC/EMI regulations.MODELTEPS65F05TEPS65F12TEPS65F12-HTEPS65F24TEPS65F24-HMAX OUTPUT WATTAGE [W]*250.065.465.4 (90.0)66.066.0 (90.0)DC OUTPUT*25V 10.0A12V 5.45A12V 5.45 (7.50)A24V 2.75A24V 2.75 (3.75)ASPECIFICATIONSMODELTEPS65F05TEPS65F12TEPS65F12-HTEPS65F24TEPS65F24-HVOLTAGE [VAC]*285 - 264 1f(Refer to“Derating”and Instruction Manual 3.1)CURRENT [A]FREQUENCY [Hz]50 / 60 (45 - 66)INPUTACIN 100V 90.0typ 91.5typ 91.5typ 92.5typ 92.5typEFFICIENCY [%]ACIN 230V 91.5typ 93.0typ 93.0typ 93.5typ 93.5typACIN 100V 30typ (Io=100%) Ta=25C at cold startINRUSH CURRENT [A]ACIN 230V 65typ (Io=100%) Ta=25C at cold startLEAKAGE CURRENT [mA]0.25max (ACIN 264V, 60Hz, Io=100%, According to IEC62368-1, and DEN-AN)VOLTAGE [V]512122424CURRENT [A]*210.05.455.45 (Peak 7.50)2.752.75 (Peak 3.75)LINE REGULATION [mV]*320max48max48max96max96maxLOAD REGULATION [mV] *340max100max100max150max150maxRIPPLE[mVp-p]*4 -10 to +50C *5240max300max300max360max360maxOUTPUTRIPPLE NOISE[mVp-p] *4 -10 to +50C *5 300max 380max 380max 480max 480maxTEMPERATURE0 to +50C *5 50max 120max 120max 240max 240maxREGULATION [mV]-10 to +50C *560max150max150max290max290maxDRIFT [mV]*620max48max48max96max96maxSTART-UP TIME [ms]500typ (ACIN 100/230V, Io=100%)HOLD-UP TIME [ms]10typ (ACIN 100V, Io=80%) / 60typ (ACIN 230V, Io=100%)OUTPUT VOLTAGE SETTING [V] 4.90 to 5.3011.50 to 12.5011.50 to 12.5023.00 to 25.0023.00 to 25.00OVERCURRENT PROTECTION Works over 105% of rating (works over 101% of peak current at option -H) and recovers automaticallyPROTECTIONOVERVOLTAGE PROTECTION [V] 5.50 to 6.50 13.20 to 15.60 13.20 to 15.60 26.40 to 31.20 26.40 to 31.20CIRCUIT ANDOPERATING INDICATION Not providedOTHERSREMOTE SENSINGNot providedISOLATIONINPUT-OUTPUT3,000VAC 1minute, Cutoff current = 10mA, 500VDC 100MW min (At Room Temperature)OPERATING TEMP.,HUMID.AND ALTITUDE *2-10 to +70C, 20 - 90%RH (Non condensing), (Refer to“Derating”), 5,000m (16,500feet) maxENVIRONMENTIMPACT196.1m/s 2 (20G), 11ms, once each X, Y and Z axisSAFETY ANDAGENCY APPROVALSUL62368-1, C-UL (equivalent to CAN/CSA-C22.2 No.62368-1), EN62368-1, Complies with DEN-ANNOISECONDUCTED NOISE*7Complies with CISPR11-B, CISPR32-B, EN55011-B, EN55032-B, FCC Part 15-B, FCC Part 18-B, VCCI-BREGULATIONSHARMONIC ATTENUATOR *8Complies with IEC61000-3-2 (Class A) (No built-in power factor correction)OTHERS*1The listed options may affect the published standard specifications. Please contact us for detailed product specifications.*2Derating is required. ( ) means peak current. There is a possibility that an internal device is damaged when the specification is exceeded. Please contact us about the detail.*3At low load conditions, the burst mode operation will start. To check load regulation, you will need to measure the characteristics at average mode with instruments.*4This is the value that measured on measuring board with capacitor of 22μF and 0.1μF at 50mm from output terminal.(Refer to Instruction Manual)*512V output product, the maximum temperature of 45C.*6Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C, with the input voltage held constant at the rated input/output.*7When secondary circuit will be connected to earth, the spec will be changed. (Refer to Instruction Manual 2)*8Please contact us about another class. When two or more units are operating it may not comply with the IEC61000-3-2. Please contact us for details.*To meet the specification, do not operate overload condition.*Parallel operation is not possible.*Sound noise may be emitted from the power supply depending on operating conditions.TEPS-14? 262 ?